TRAINING PNEUMATIC DAN SISTEM HIDROLIS

TRAINING PNEUMATIC DAN SISTEM HIDROLIS

DESKRIPSI
Sistem otomasi dunia industri berkembang pesat seiring semakin tingginya teknologi yang digunakan. Begitu pula dengan perangkat elektro pneumatic dan hydraulic yang digunakan dunia industri dan manufaktur. Sebagian besar industri mengimplementasikan sistem pneumatic dan hydraulic dalam instalasinya.

Melalui pelatihan ini para peserta diharapkan dapat meningkatkan pengetahuan dan wawasan mengenai nama, fungsi, simbol, cara kerja dan kemampuan masing-masing komponen pneumatic & hydraulic. Pelatihan ini akan memberikan pemahaman mengenai komponen-komponen dasar dan fungsi dari sistem hydraulic dan pneumatic. Topik yang akan dipelajari meliputi: standard symbols, pumps, motor system, control valves, control assemblies, actuators, FRL, maintenance procedures, and switching and control devices. Diharapkan peserta akan dapat memahami mengenai pengoperasian fluid power system, termasuk desain, aplikasi dan troubleshooting.

Tujuan :
•    Mengetahui proses mekanisasi proses industri yang berkaitan dengan sistem pneumatic & hydraulic;
•    Mengetahui teknik otomasi mesin;
•    Mengetahui tentang penerapan sistem pneumatic & hydraulic di industri;
•    Mengatahui dasar-dasar perancangan dan desain sistem pneumatic & hydraulic;
•    Mengetahui elektro pneumatic & hydraulic;
•    Memberikan pengetahuan tentang pengoperasian dan pemeliharaan sistem pneumatic & hydraulic beserta troubleshooting-nya.

MATERI

1. Introduction to Fluid Power
•    What is Fluid Power
•    Advantages of Fluid Power
•    Applications of Fluid Power
•    Components of Fluid Power Systems
2. Power Transmitting Fluids
•    Fluids: Oil and Air
•    Pressure, Head, and Force
•    The Perfect Gas Law
•    The Continuity Equation
•    Bernoulli’s Equation
•    Pascal’s Law and Application
•    Bulk Modulus
•    Pressure Losses in Valve and Fitting
•    Flow and Pressure Measurement
•    Energy, Power, and Flow Rates
3. Basic Fluid Power System
•    The Basic Pneumatic System
•    The Basic Hydraulic System
•    Air Compressors
•    Hydraulic Pump
•    Pump Performance
•    Pump Selection
•    Pressure Intensifiers
•    Motors and Actuators
•    Hydraulic Motor Performance
•    Low-Speed, High-Torque Motors
4. The Distribution System
•    Steel Pipes, Steel Tubing and Plastic Tubing
•    Flexible Hoses
•    Quick Disconnect Coupling
•    Metric Steel Tubing
5. Control Components and Simple Circuit
•    Directional Control Valve
•    Pressure and Flow Control Valve
•    Servo Valve
•    Hydraulic Fuses
•    Pressure and Temperature Switches
•    Shock Absorbers
6. Hydraulic Circuit
•    Control of a Single and Double-Acting Hydraulic Cylinder
•    Regenerative Circuit
•    Pump-Unloading Circuit
•    Double-Pump Hydraulic System
•    Pressure Intensifier Circuit
•    Counterbalance Valve Application
•    Hydraulic Cylinder Sequencing Circuit
•    Automatic Cylinder Reciprocating System
•    Locked Cylinder Using Pilot Check Valves
•    Cylinder Synchronizing Circuit
•    Metering in and Metering out Fail-Safe Circuits
•    Speed Control of Hydraulic Motor
•    Hydraulic Motor Breaking System
•    Accumulators and Accumulator Circuit
7. Pneumatic Circuit
•    Fluid Conditioners
•    Air Service Unit
•    Air Pressure Losses in pipes
•    Control with Orifice
•    Air Control Valve
•    Pneumatic Actuators
•    Basic Pneumatic Circuit
•    Circuit Design with Intuitive and Cascade Method
•    Accumulator System Analysis
•    Pneumatic Circuit Analysis
8. Electrical Controls for Fluid Power Circuit
•    Electrical Components
•    Control of a Cylinder Using a Single Limit Switch
•    Dual Cylinder Sequence Circuits
•    Electrical Control of Regenerative Circuit
•    Counting, Timing, and Reciprocation of Hydraulic Cylinder
•    Programmable Logic Controllers (PLC)
9. Fluid Power Maintenance and Safety
•    Sealing Devices
•    The Reservoir System
•    Filters and Strainers
•    Filtration and Contamination Assessment
•    Beta Ratio of Filters
•    Temperature Control
•    Troubleshooting Fluid Power Circuit
•    Safety Considerations
•    General problems and solutions

PESERTA
Para Foreman, Technician, Technical Assistance, Engineer, Mechanics, Supervisor, Inspection & Repair Managers, Operator, serta Tenaga lapangan yang menangani pneumatic & hydraulic power system.

TRAINING METHOD

• Group Discussions
• Group & Individual Exercises
• Presentations
• Games
• Case Studies
• Role Plays
• Self-Assessment
• Action Plan

FACILITIES

• Certificate,
• Quality Training Kit (Pencil case: Erase, Bolpoint, Pencil, Tipe X, Stabillo, Flash Disk 8 GB),
• Bag.
• Training Material (HandOut & SoftCopy)
• Convenient training facilities in stars hotel (Public Training)
• Lunch and Coffee Breaks (Public Training)
• Souvenir

Permintaan Brosur penawaran Training ( Harga, Waktu dan Tempat) silahkan Menghubungi kami.

Catatan :

• Pelatihan ini dapat di-customized sesuai kebutuhan perusahaan Anda bila diselenggarakan dalam bentuk In-House Training. Untuk permintaan In-House Trainingdengan jenis topik lainya, silahkan mengirimkan ke alamat email yang tercantum di web kami.
• Request Training. Jika anda membutuhkan informasi pelatihan yang belum tercantum pada website ini, atau anda ingin memberikan usulan materi yang sesuai dengan tingkat kebutuhan perusahaan anda, silahkan mengirimkan ke alamat emailyang tercantum.
• Bila tidak ada tanggal dan waktu atau yang tercantum sudah kadaluarsa didalam artikel mohon tanyakan kepada kami untuk jadwal terbarunya.
• Peserta bisa mengajukan Tanggal Pelatihan / Training selain yang tertera pada silabus penawaran.

 

Info Jadwal Training , Training, Training di Bandung, Training di Jakarta, Training di Bali, Training di Yogyakarta, Training di Lombok, Training di Surabaya, Training di Malang, Training di Solo, Training di Medan, Training di Manado, Training di Batam, Training di Semarang, Training di Bogor,